ALLGEMEINE BESCHREIBUNG

The REF19x series precision band gap voltage references use a patented temperature drift curvature correction circuit and laser trimming of highly stable, thin-film resistors to achieve a very low temperature coefficient and high initial accuracy.
The REF19x series is made up of micropower, low dropout voltage (LDV) devices, providing stable output voltage from supplies as low as 100 mV above the output voltage and consuming less than 45 μA of supply current. In sleep mode, which is enabled by applying a low TTL or CMOS level to the SLEEP pin, the output is turned off and supply current is further reduced to less than 15 μA.
The REF19x series references are specified over the extended industrial temperature range (−40°C to +85°C) with typical performance specifications over −40°C to +125°C for applications, such as automotive.
All electrical grades are available in an 8-lead SOIC package; the PDIP and TSSOP packages are available only in the lowest electrical grade.

 

FEATURES

Temperaturkoeffizient: maximal 5 ppm/°C
Hoher Ausgangsstrom: 30 mA
Niedriger Versorgungsstrom: maximal 45 μA
Anfangsgenauigkeit: ±2 mV maximal1
Schlafmodus: 15 μA maximal
Niedrige Dropout-Spannung
Lastregelung: 4 ppm/mA
Leitungsregelung: 4 ppm/V
Schutz gegen Kurzschluss

 

ANWENDUNGEN

Tragbare Instrumente
ADCs und DACs
Intelligente Sensoren
Solarbetriebene Anwendungen
Schleifenstrom-gespeiste Instrumente

 

ANWENDUNGSINFORMATIONEN

KURZSCHLUSSVERHALTEN DES AUSGANGS

Die Geräte der REF19x-Familie sind vollständig vor Schäden durch versehentliche Kurzschlüsse am Ausgang gegen GND oder gegen VS geschützt. Im Falle eines versehentlichen Kurzschlusses schaltet sich das Referenzgerät ab und begrenzt seinen Versorgungsstrom auf 40 mA.

ÜBERLEGUNGEN ZUR VERLUSTLEISTUNG DES GERÄTS

Die Referenzgeräte der REF19x-Familie können Lastströme bis zu 30 mA bei einer Eingangsspannung von 3,3 V bis 15 V liefern. Wenn diese Geräte in Anwendungen mit hohen Eingangsspannungen eingesetzt werden, sollten Sie darauf achten, dass die maximale interne Verlustleistung dieser Geräte nicht überschritten wird. Ein Überschreiten der veröffentlichten Spezifikationen für die maximale Verlustleistung oder die Sperrschichttemperatur kann zu einem vorzeitigen Ausfall des Geräts führen.

ÜBERBRÜCKUNG DER AUSGANGSSPANNUNG

Für einen stabilen Betrieb benötigen Low-Dropout-Spannungsregler und Referenzen in der Regel einen Bypass-Kondensator, der von den VOUT-Pins zu den GND-Pins geschaltet wird. Obwohl die REF19x-Referenzfamilie einen stabilen Betrieb mit kapazitiven Lasten von mehr als 100 μF ermöglicht, ist ein 1 μF-Kondensator ausreichend, um die Nennleistung zu garantieren. Die Hinzufügung eines 0,1 μF Keramikkondensators parallel zum Bypass-Kondensator verbessert das Einschwingverhalten des Laststroms. Für ein optimales Einschwingverhalten der Netzspannung wird empfohlen, die Spannungseingänge dieser Geräte mit einem 10 μF Elektrolytkondensator parallel zu einem 0,1 μF Keramikkondensator zu überbrücken.

BETRIEB IM SCHLAFMODUS

All REF19x devices include a sleep capability that is TTL/CMOSlevel compatible. Internally, a pull-up current source to VS is connected at the SLEEP pin. This permits the SLEEP pin to be driven from an open collector/drain driver. A logic low or a 0 V condition on the SLEEP pin is required to turn off the output stage. During sleep, the output of the references becomes a high impedance state where its potential would then be determined by external circuitry. If the sleep feature is not used, it is recommended that the SLEEP pin be connected to VS .
Applications often require digital control of reference voltages, selecting between one stable voltage and a second. With the sleep feature inherent to the REF19x series, switched output reference configurations are easily implemented with little additional hardware.

TEST-PINS

Test Pin 1 und Test Pin 5 sind für das Zener-Zapping im Gehäuse reserviert. Um ein Höchstmaß an Genauigkeit am Ausgang zu erreichen, wird die Zener-Zapping-Technik zum Trimmen der Ausgangsspannung verwendet. Da jedes Gerät eine unterschiedliche Anpassung erfordert, variiert der Widerstandswert an den Testpins von Pin zu Pin und von Teil zu Teil. Der Benutzer sollte Pin 1 und Pin 5 unbeschaltet lassen.