Descripción

The MC100LVEL16 is a differential receiver. The device is functionally equivalent to the EL16 device, operating from a 3.3 V supply. The LVEL16 exhibits a wider VIHCMR range than its EL16 counterpart. With output transition times and propagation delays comparable to the EL16 the LVEL16 is ideally suited for interfacing with high frequency sources at 3.3 V supplies.
Under open input conditions, the Q input will be pulled down to VEE and the Q input will be biased to VCC/2. This condition will force the Q output low.
The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 F capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open.

 

Características

-300 ps Propagation Delay
-High Bandwidth Output Transitions
-The 100 Series Contains Temperature Compensation
-PECL Mode Operating Range: VCC = 3.0 V to 3.8 V with VEE = 0 V
-NECL Mode Operating Range: VCC = 0 V with VEE = −3.0 V to −3.8 V
-Internal Input Pulldown Resistors on D, Pullup and Pulldown Resistors on D
-Q Output will Default LOW with Inputs Open or at VEE
-These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant

 

ATTRIBUTES

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected.
1.JEDEC standard multilayer board − 2S2P (2 signal, 2 power)
2.Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3.Input and output parameters vary 1:1 with VCC. VEE can vary 0.3 V.
4.Outputs are terminated through a 50 resistor to VCC − 2 V.
5.VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
6.Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
7.VEE can vary ±0.3 V.
8.Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
9.VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of≈40.
10.Refer to Application Note AND8003/D for additional information.

 

ORDERING INFORMATION

For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “,” may or may not be present. Some products may not follow the Generic Marking.
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07.